OOAK Table Tennis Forum

I am annoyed with the powder on the new balls, it sticks to the rubber, and I think up to some extent it will do abrasion to the rubber during play and will reduce spin also. Even after cleaning it with damp cloth, some still remains on the ball. However it seems that I am the only one that is annoyed, my friends do not care to clean the new balls.I do not know if it is the same case with the plastic balls. Anybody gets annoyed like me ?

_________________
Roots 9 C-Pen
Red Acuda P2

Last week I set up the iPong v300 and brought out a never-used-before box of Double Fish 1 star celluloids. Talk about dust! Wow... big white spots on the rubber, the black rubber turned white. It was like sprinkling talcum powder. Made the tacky H3 untacky. Now, despite this - it didn't bounce the ball any higher than when it was clean! (We've been discussing H3 elsewhere, and why it bounces the ball so low but hits pretty hard if you swing hard at the ball.)

Iskandar

I've found the robot, with old celluloid training balls, covered my rubbers in dust. I find after a lengthy multiball session, my rubber is covered in white dust. I just clean the rubber and continue. Not worth being annoyed about.

_________________
"When one eye is fixed upon your destination, there is only one eye left with which to find the Way."

Read my blog: "LordCope's Latest Learnings Log": http://ooakforum.com/viewtopic.php?f=58&t=24452

For robot use, I always recommend people to wash the balls first. Just put them in a bucket of water it it's gone.

I find it annoying too. I know some players would put the ball in their mouth to get the dust off....disgusting habit but it works.

_________________
OOAK Table Tennis Shop | Re-Impact Blades | Butterfly Table Tennis bats
Setup1: Re-Impact Smart, Viper OX, Victas VS 401 Setup2: Re-Impact Barath, Dtecs OX, TSP Triple Spin Chop 1.0mm Setup3: Re-Impact Dark Knight, Hellfire OX, 999 Turbo
Recent Articles: Butterfly Tenergy Alternatives | Tenergy Rubbers Compared | Re-Impact User Guide

I use a damp cloth on new balls, better the licking it clean. I don't want to ingest any plastic mould release powder.

_________________
Custom SoulSpin Limba/ALC
FH: Tibhar Evo MX-P Max
BH: Xiom Omega V Pro Max

Of the new plastic balls really only noticed on the NP 40+

+1

Plastic balls don't seem to have the issue.

_________________
I'm always in the dark, but the Dark sheds lights upon everything!! Beauty is only pimple deep! Beauty is in the eye of the pipholder!
S/U 1: Blade: Bty Gergely . FH Black Andro Rasant 2.1 . BH Red Tibhar Grass Dtecs
S/U 2: Blade: Bty Gergely . FH Black Hexer+ 2.1 . BH Red GD Talon
S/U 3: Blade: Bty Gergely . No rubbers...thinking of adding Red Dtecs and Black Rasant
Aussie Table Tennis Shop / Aussie Table Tennis Facebook Page / Equipment Review Index / Read my Reb Report Blog: click here.

Thanks for all your comments. I still think that dust will reduce grippynes on the rubber.

_________________
Roots 9 C-Pen
Red Acuda P2

Certainly, that white scurf on the ball will make the ball less spinny. It needs to be cleaned off before playing. Just do it !!! Patented in Germany.

https://www.tabletennisdaily.com/forum/ ... bber/page2

Personally I think this needs to be done at the factory... we should not need to buy a device just to clean a ball that's brand new.

I like the idea of the device though. Sounds like all we need is something slightly abrasive to rub off all the dust, because just water does not seem to do the job well.

Some balls are a lot worse (for dust) than others. The worst one I've found if the Double fish ball... this one has the roughest finish I've seen, which seems to retain the dust for a long time. It's not a bad ball, but the rough finish and dust is a little off putting.

_________________
OOAK Table Tennis Shop | Re-Impact Blades | Butterfly Table Tennis bats
Setup1: Re-Impact Smart, Viper OX, Victas VS 401 Setup2: Re-Impact Barath, Dtecs OX, TSP Triple Spin Chop 1.0mm Setup3: Re-Impact Dark Knight, Hellfire OX, 999 Turbo
Recent Articles: Butterfly Tenergy Alternatives | Tenergy Rubbers Compared | Re-Impact User Guide

The manufacturer of the Praktissmate robot I have specifically tells you to treat new balls by cleaning them with vegetable oil to get the dust off. Worked well, as I purchased 300 cheap Chinese brand balls that were coated in dust. Afterwards they were fine.

I don't recall whether or not I followed that up with detergent or let the oil dissipate. Been a while.

_________________
Blog: "Holy Chtchet!" ⇝ Rating: 1615

Projects: Player Equipment Grid ⇝ Comprehensive Thin Inverted Chopping Rubbers Grid ⇝ Please send me corrections or new submissions

One of the few pros of having powder on the ball, you get a very good idea of where on the rubber you are contacting the ball.

_________________
Retriever (sometimes golden, but often leaden)
Moderator, Inverted Retriever Technique sub-forum - http://ooakforum.com/viewforum.php?f=74

Oh come on... there was powder on the old balls, too. In fact there was powder on the historic 38mm three star Nittakus that we thought were so wonderful back in the day.

Iskandar

Yes, but it's much worse with some of the current plastic balls, a lot more dust comes off, and it takes longer for it to wear off.

_________________
OOAK Table Tennis Shop | Re-Impact Blades | Butterfly Table Tennis bats
Setup1: Re-Impact Smart, Viper OX, Victas VS 401 Setup2: Re-Impact Barath, Dtecs OX, TSP Triple Spin Chop 1.0mm Setup3: Re-Impact Dark Knight, Hellfire OX, 999 Turbo
Recent Articles: Butterfly Tenergy Alternatives | Tenergy Rubbers Compared | Re-Impact User Guide