OOAK Table Tennis Forum
https://ooakforum.com/

elmer's glue?
https://ooakforum.com/viewtopic.php?f=9&t=23826
Page 2 of 2

Author:  iskandar taib [ 02 Feb 2019, 02:44 ]
Post subject:  Re: elmer's glue?

Hmmm.. and if you don't press it under the books what happens?

Iskandar

Author:  tommyngo [ 03 Feb 2019, 02:48 ]
Post subject:  Re: elmer's glue?

:lol: :lol: :lol: hm..hm.. Someone forgets his common sense at home .... :rofl: :rofl:

Author:  iskandar taib [ 06 Feb 2019, 13:36 ]
Post subject:  Re: elmer's glue?

You mean is DOESN'T work if you don't use the books???? I NEVER have to use books to press on the racket when using Elmer's Rubber Cement. It just sticks. Never had to do it with water-based table tennis glues, either.

Iskandar

Author:  tommyngo [ 08 Feb 2019, 02:13 ]
Post subject:  Re: elmer's glue?

iskandar taib wrote:
You mean is DOESN'T work if you don't use the books???? I NEVER have to use books to press on the racket when using Elmer's Rubber Cement. It just sticks. Never had to do it with water-based table tennis glues, either.

Iskandar


Elmer's RC is much more fast drying compared to Elmer's clear school glue . The key to my method is : spread very thin layer of glue uniformly on both the sponge and the blade ( i.e. using a discarded credit card) then press down the rubber onto on the blade to assure completely full contact to solidify the bond . I also use electrical tapes around the edge and on the rubber as seen in the enclosed photo .

This way further secures the rubbers onto the blade around the edge . I also add a sponge edge tape to protect the paddle against accidental contact with the table . The overall additional attachments ( i.e. electrical tapes + sponge edge tape ) add about 4 grams to the weight of the paddle .

Note that I play for pleasure so ITTF rules should not be a concern for me as far as edge tape is concerned.. :D :D

I just told you my experience ...and it worked very well for me . BTW, Elmer's clear school glue costs 1.77 $ US ( 147. cc) compared to 4.49$ U.S for 118.cc of Elmer's RC ( i.e. selling prices at Walmart stores in U.S.A. )


Image

Author:  Japsican [ 09 Feb 2019, 01:43 ]
Post subject:  Re: elmer's glue?

iskandar taib wrote:
The washable school glue might indeed behave differently than the old Elmer's White Glue. If you apply the old Elmer's Glue to a piece of wood and allow it to soak in an dry it will NEVER come off, since it's meant for gluing pieces of wood together. The Washable School Glue might behave differently, but I'm not going to try it. It's not available everywhere here, like it would be in the US.

Iskandar

Exactly. White glue will destroy it.

And for the Washable School Glue...the big question is... WHY? I can't see how it could get better than RC is right now, which is perfect except for the VOCs which I could care less. But if it works, it is viable in comparison to Water Based TT glue, because the cost is considerably less. And it's cheaper than Tear Mender. So that I can see....but still seems inconvenient.

Author:  Japsican [ 09 Feb 2019, 02:01 ]
Post subject:  Re: elmer's glue?

Compared to RC

Disadvantages
Credit card needed to spread it out
Heavy books needed
Rubber may slide after mounting requiring tape
Slow drying needing electric fan

Advantages
No Harmful VOCs
Potentially can be used on Tensors since no VOCs

Cost is a non-factor here in the US. IT's a few cents difference.... ($1.99 for 4 oz of RC vs. 1.79 for 5 oz of Clear glue at Target).

Still unknown if you RE-glue the rubber without applying more glue to the rubber. RC does not need this.

Hasn't been tested long term for effects on blade and sponge.


------------------------------

Compared to WBG

Disadvantages
Credit card needed to spread it out
Heavy books needed
Rubber may slide after mounting requiring tape
Slow drying needing electric fan

Advantages
Cost only.

Author:  tommyngo [ 09 Feb 2019, 02:27 ]
Post subject:  Re: elmer's glue?

Japsican wrote:

......

Still unknown if you RE-glue the rubber without applying more glue to the rubber. RC does not need this. .....



I always peel off the old glue from the sponge & the blade before re-gluing . It comes off very easily . I hate the smell of rubber cement and avoid using it at all cost . It's a personal preferrence.

BTW, if you apply a very thin glue layer, one hour of weight pressing down the rubber is good enough . So far, I apply my method on 8 blades and they work fine .

Author:  iskandar taib [ 09 Feb 2019, 03:13 ]
Post subject:  Re: elmer's glue?

tommyngo wrote:

Elmer's RC is much more fast drying compared to Elmer's clear school glue . The key to my method is : spread very thin layer of glue uniformly on both the sponge and the blade ( i.e. using a discarded credit card) then press down the rubber onto on the blade to assure completely full contact to solidify the bond . I also use electrical tapes around the edge and on the rubber as seen in the enclosed photo .

This way further secures the rubbers onto the blade around the edge . I also add a sponge edge tape to protect the paddle against accidental contact with the table . The overall additional attachments ( i.e. electrical tapes + sponge edge tape ) add about 4 grams to the weight of the paddle .

Note that I play for pleasure so ITTF rules should not be a concern for me as far as edge tape is concerned.. :D :D

I just told you my experience ...and it worked very well for me . BTW, Elmer's clear school glue costs 1.77 $ US ( 147. cc) compared to 4.49$ U.S for 118.cc of Elmer's RC ( i.e. selling prices at Walmart stores in U.S.A. )


Image


So it's still wet and trying to dry when you assemble the racket, no allowing the glue to dry like you would with a contact cement. I suppose if it works, it works, I'm am surprised the water finds its way out from in between the rubber and the wood. Yeah, that "edge tape" isn't just edge tape... :lol:

Yeah, rubber cement is more expensive, it costs somewhat more here, too. But I buy the big half pint bottles and use those to refill the small one with the brush. Cheaper that way, and the glue doesn't get a chance to become thicker in the small bottle (which it will before you get a chance to use all of it).

Iskandar

Author:  iskandar taib [ 09 Feb 2019, 03:17 ]
Post subject:  Re: elmer's glue?

Japsican wrote:
Compared to RC

Disadvantages
Credit card needed to spread it out
Heavy books needed
Rubber may slide after mounting requiring tape
Slow drying needing electric fan

Advantages
No Harmful VOCs
Potentially can be used on Tensors since no VOCs



I get most of the above, but why would a VOC based rubber cement be a problem when gluing Tensors in particular? I've done it with several sheets, haven't had any problems at all.

Iskandar

Author:  Japsican [ 09 Feb 2019, 22:45 ]
Post subject:  Re: elmer's glue?

iskandar taib wrote:
Japsican wrote:
Compared to RC

Disadvantages
Credit card needed to spread it out
Heavy books needed
Rubber may slide after mounting requiring tape
Slow drying needing electric fan

Advantages
No Harmful VOCs
Potentially can be used on Tensors since no VOCs



I get most of the above, but why would a VOC based rubber cement be a problem when gluing Tensors in particular? I've done it with several sheets, haven't had any problems at all.

Iskandar


Depends on who you talk to and the rubber. Butterfly and ESN explicitly state you shouldn’t use RC or else it somehow is detrimental to their spring sponge/tensor rubbers. I agree with you that it’s no big deal, but I have noticed far more shrinkage on re-gluing when RC is used on tensors. I actually did a test with 2 sheets of Xiom Vega Europe... one rubber with WBG and the other with RC. There was more shrinkage on re-gluing, not a ton, but it wasn’t negligent. For this reason, I do the method where I use WBG on the tensor and RC on the blade. If not a tensor, then RC both surfaces.

All tensor shrink some, but it does seem more so if RC is put directly on the sponge. I have only done the direct comparison once though.

Page 2 of 2 All times are UTC + 9:30 hours
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/