OOAK Table Tennis Forum


A truly International Table Tennis Community for both Defensive and Offensive styles!
OOAK Forum Links About OOAK Table Tennis Forum OOAK Forum Memory
It is currently 19 Nov 2018, 01:55


Don't want to see any advertising? Become a member and login, and you'll never see an ad again!



All times are UTC + 9:30 hours




Post new topic Reply to topic  [ 7 posts ] 
Author Message
PostPosted: 28 Jun 2018, 13:40 
Offline
003 Style Master
003 Style Master
User avatar

Joined: 27 Apr 2011, 20:23
Posts: 2237
Location: South Australia
Has thanked: 258 times
Been thanked: 270 times
Blade: Donic Waldner Senso V1
FH: Joola Rhyzm 425
BH: Donic Baracuda Big Slam
A few weeks ago I hit my blade pretty hard on the end of the table causing a dent at the end which has also caused the top ply to lift slightly due to the end being pushed in a bit, perhaps 0.5 of a mm. Note this is nothing new, its a pretty standard dent but perhaps just a fraction deeper. It was a hard knock.

It now means when putting on a rubber, there is a little raised bit right at the end of my bat where the top ply is a fraction higher. I'm wondering whether to fix it or not. One option is to sand the raised bit but it will mean its likely to completely sand away the top ply in that little part. Since its not likely to affect performance it wouldn't matter but wondering if the top ply is removed, is it more likely to cause splintering or cracking elsewhere.

Should I sand or just leave it? Note that I'm likely to be selling the bat to a club member so on one hand sanding would make it look nice but at the same time don't want to be deceiving them.

_________________
Donic Waldner Senso V1,FH Joola Rhyzm 425 2.0mm ,BH Donic Baracuda Big Slam 2.0mm


Top
 Profile  
 


Don't want to see this advertisement? Become a member and login, and you'll never see an ad again!

PostPosted: 28 Jun 2018, 13:57 
Offline
Do you feel lucky (young) punk?
Do you feel lucky (young) punk?
User avatar

Joined: 27 Mar 2007, 12:57
Posts: 5490
Location: USA
Has thanked: 72 times
Been thanked: 153 times
You could try putting a wet rag on just the damaged part for 10 minutes. Then lightly clamp the area between two wood blocks for a couple days. Might work. :)


Top
 Profile  
 
PostPosted: 28 Jun 2018, 14:16 
Offline
Hurricane Lover
Hurricane Lover
User avatar

Joined: 09 Mar 2008, 19:19
Posts: 2657
Location: Indonesia
Has thanked: 134 times
Been thanked: 179 times
Blade: DHS Long 2
FH: Dianchi D
BH: Yinhe Pluto
Fixing the blade a little or a lot doesn't equal deceiving people.

I have many blades with cracks and dents small to big... Some I got it fixed properly, some I just use super glue to hold it together... Some of them fixed properly or not I sell to others...

Posting a photo of the part in question would go a long way for some of us to offer better suggestion on what could be done.

instagram: rokphishtt

_________________
instagram: rokphishtt


Top
 Profile  
 
PostPosted: 28 Jun 2018, 14:41 
Offline
Dark Knight
Dark Knight
User avatar

Joined: 13 Dec 2006, 12:34
Posts: 32044
Location: Adelaide, AU
Has thanked: 1676 times
Been thanked: 1138 times
Blade: Trinity Carbon
FH: Victas VS > 401
BH: Dornenglanz OX
I know some people will fill small dents with something, then sand it down till it's flat. If it's in the middle of the blade surface, this seems worthwhile.

Does anyone have experience with the best material used to fill the dent?

_________________
OOAK Table Tennis Shop | Re-Impact Blades | Butterfly Table Tennis bats
Setup1: Re-Impact Smart, Viper OX, Victas VS 401 Setup2: Re-Impact Barath, Dtecs OX, TSP Triple Spin Chop 1.0mm Setup3: Re-Impact Dark Knight, Hellfire OX, 999 Turbo
Recent Articles: Butterfly Tenergy Alternatives | Tenergy Rubbers Compared | Re-Impact User Guide


Top
 Profile  
 
PostPosted: 28 Jun 2018, 15:11 
Offline
Call me Shrek!
User avatar

Joined: 25 May 2011, 12:38
Posts: 973
Location: California, USA
Has thanked: 9 times
Been thanked: 76 times
Blade: Hallmark Ultra
FH: Tenergy 05 FX max
BH: Rakza 7 Soft max
When I was about 14 years old, I cracked the top of my blade (not just splintered - actually cracked ). The two sides were slightly misaligned - I used resin filller to fill the gap, slightly overfilling, and then sanding down both sides. 30 years later, the bat is still going strong...

Where the ply has lifted or a small piece has detached, I just use superglue to put it back


Top
 Profile  
 
PostPosted: 28 Jun 2018, 16:43 
Offline
003 Style Master
003 Style Master
User avatar

Joined: 27 Apr 2011, 20:23
Posts: 2237
Location: South Australia
Has thanked: 258 times
Been thanked: 270 times
Blade: Donic Waldner Senso V1
FH: Joola Rhyzm 425
BH: Donic Baracuda Big Slam
The dent is flush on the end of the blade, the bit you cover with edge tape. What it has done though is that as there is a small amount of week that has been compressed due to the knock, the top ply has been forced upward slightly. Note that its all still attached, there is no splinter. Its just a typical bang on the table but a good one. :clap:

_________________
Donic Waldner Senso V1,FH Joola Rhyzm 425 2.0mm ,BH Donic Baracuda Big Slam 2.0mm


Top
 Profile  
 
PostPosted: 28 Jun 2018, 19:56 
Offline
003 Style Master
003 Style Master
User avatar

Joined: 27 Apr 2011, 20:23
Posts: 2237
Location: South Australia
Has thanked: 258 times
Been thanked: 270 times
Blade: Donic Waldner Senso V1
FH: Joola Rhyzm 425
BH: Donic Baracuda Big Slam
In the end I just sanded the raised but a little and it was fine. Didn't with about using filler on the end as edge tape covers and wasn't that bad anyway.

_________________
Donic Waldner Senso V1,FH Joola Rhyzm 425 2.0mm ,BH Donic Baracuda Big Slam 2.0mm


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 7 posts ] 




All times are UTC + 9:30 hours


Who is online

Users browsing this forum: No registered users and 24 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Copyright 2018 OOAK Table Tennis Forum. The information on this site cannot be reused without written permission.

Powered by phpBB® Forum Software © phpBB Group




Don't forget to 'LIKE' our forum on Facebook if you enjoy the content: