OOAK Table Tennis Forum

MB torn to pieces , and the blade i am still using...

but some1 is selling that blade rubber combo on the forum i think...

_________________
My TT blog
I must not fear. Fear is the mind-killer. Fear is the little death that brings total obliteration. I will face my fear. I will permit it to pass over me and through me. And when it has gone past I will turn my inner eye to see its path. Where the fear has gone there will be nothing. Only I will remain.

found it...here it is...

viewtopic.php?f=10&t=31166

_________________
My TT blog
I must not fear. Fear is the mind-killer. Fear is the little death that brings total obliteration. I will face my fear. I will permit it to pass over me and through me. And when it has gone past I will turn my inner eye to see its path. Where the fear has gone there will be nothing. Only I will remain.

Hi there! What's up in your part of the table tennis world? Any change of setup or any other changes? Be well!

_________________
My blog: Def-attack's attempts to find balance between defence/attack | Serving techniques and strategy section

hi m8, tnx for asking...

like every summer i am taking a break from tt and play only big tennis, my tt season start in September...

equipment wise, i have switched to drN ABS fanti...it is not as good as MB ot Transformer while they are new, but it stay the same and its good enough long after i would have needed to change MB...and that is more important to me bcs i cant afford to switch fanti every month or two...further testing will be when season starts...

_________________
My TT blog
I must not fear. Fear is the mind-killer. Fear is the little death that brings total obliteration. I will face my fear. I will permit it to pass over me and through me. And when it has gone past I will turn my inner eye to see its path. Where the fear has gone there will be nothing. Only I will remain.

How often are you having to change the transformer? Question for everyone. I'd want the anti (expensive) to last 2 months at least.

_________________
Blog: "Holy Chtchet!" ⇝ Rating: 1615

Projects: Player Equipment Grid ⇝ Comprehensive Thin Inverted Chopping Rubbers Grid ⇝ Please send me corrections or new submissions

To be fair, it can last 2 months, but after the 1st one you can tell that the reversal is not at 100 percent...

_________________
My TT blog
I must not fear. Fear is the mind-killer. Fear is the little death that brings total obliteration. I will face my fear. I will permit it to pass over me and through me. And when it has gone past I will turn my inner eye to see its path. Where the fear has gone there will be nothing. Only I will remain.

Iceman, DA mentioned you had a video of how to glue transformer to the blade. I see the one where you take it off, but not where you attach by using a glue sheet. He said you apply glue to the glue sheet? Can you link me to that, or explain it? I just got my first Transfirmer in and I don't want to mess it up. I

_________________
Blog: "Holy Chtchet!" ⇝ Rating: 1615

Projects: Player Equipment Grid ⇝ Comprehensive Thin Inverted Chopping Rubbers Grid ⇝ Please send me corrections or new submissions

Grr, hate when that happens, I have written wall of text and then accidentally deleted the post


Anyway, short version this time. Remove the protection from one side of the glue sheet. And than stick that sheet numerous times to some slick surface (I have a glass table) until you see that is not so sticky. The point is that the sheet is sticking to the blade too hard if you don't do that. Now put the protective sheet back on that now not so sticky side. Now glue the other, sticky untreated side, to the sponge. Press firmly. Now, remove the protection from the now not so sticky side.

And now put the rubber very gently on the blade and remove it couple of times again. And than put it on the blade for the final time. You don't have to press it hard.

And this is it. Easy as 1 2 3

This way you can remove the rubber from the blade easily and try it on different blades without worries... The glue sheet will stay on the sponge and not on the blade.


Uf, wall of text again

_________________
My TT blog
I must not fear. Fear is the mind-killer. Fear is the little death that brings total obliteration. I will face my fear. I will permit it to pass over me and through me. And when it has gone past I will turn my inner eye to see its path. Where the fear has gone there will be nothing. Only I will remain.

Thanks so much! Did you put glue on the sponge-side of the glue sheet? I didn't.

What I ended up doing is putting Rubber Cement on the blade.

Glue sheet directly to the sponge of the rubber (no glue, just the sheet's factory stickiness).

Put water-based glue on the other side of the glue sheet.

Pressed firm but not too firm.

We'll see if/when I decide to take it off. With the RC/WB glue between the glue sheet and the blade, I doubt it will stick to hard.

_________________
Blog: "Holy Chtchet!" ⇝ Rating: 1615

Projects: Player Equipment Grid ⇝ Comprehensive Thin Inverted Chopping Rubbers Grid ⇝ Please send me corrections or new submissions

I did not put any glue on either side... Tell me how it goes when you try to remove it... If it's not coming off, use my trick from the video you can find on my YouTube channel...

Sent from my ONE A2003 using Tapatalk

_________________
My TT blog
I must not fear. Fear is the mind-killer. Fear is the little death that brings total obliteration. I will face my fear. I will permit it to pass over me and through me. And when it has gone past I will turn my inner eye to see its path. Where the fear has gone there will be nothing. Only I will remain.

side note: adding glue is not a good idea as you add another layer between the sponge and wood which reduces reversal (even if minimaly)

_________________
Blade: Der-Materialspezialist Deluxe Carbon Forehand RITC Friendship 802 2.2 Backhand Der-Materialspezialist Reflection 0.9

There are some glue sheets thas has less glue/stickiness on one side (Gewo I believe). I used that one last time, but without trying to remove stickiness the way Iceman describes above. Instead I used a thin layer of ordinary water based glue on the blade before I attached the rubber with its glue sheet.

_________________
My blog: Def-attack's attempts to find balance between defence/attack | Serving techniques and strategy section

well that's just great. Feel like I just ruined the anti. Hopefully there isn't an appreciable difference....I'd find it hard to believe the difference is that much.

_________________
Blog: "Holy Chtchet!" ⇝ Rating: 1615

Projects: Player Equipment Grid ⇝ Comprehensive Thin Inverted Chopping Rubbers Grid ⇝ Please send me corrections or new submissions

I don't think you will notice any difference, at least I haven't.

Skickat från min SM-T580 via Tapatalk

_________________
My blog: Def-attack's attempts to find balance between defence/attack | Serving techniques and strategy section

You will/can ruin it only if you try to remove it and you do it bad...don't worry...

Sent from my ONE A2003 using Tapatalk

_________________
My TT blog
I must not fear. Fear is the mind-killer. Fear is the little death that brings total obliteration. I will face my fear. I will permit it to pass over me and through me. And when it has gone past I will turn my inner eye to see its path. Where the fear has gone there will be nothing. Only I will remain.