OOAK Table Tennis Forum


A truly International Table Tennis Community for both Defensive and Offensive styles!
OOAK Forum Links About OOAK Table Tennis Forum OOAK Forum Memory
It is currently 04 Dec 2020, 21:02


Don't want to see any advertising? Become a member and login, and you'll never see an ad again!



All times are UTC + 9:30 hours




Post new topic Reply to topic  [ 20 posts ]  Go to page Previous  1, 2
Author Message
PostPosted: 02 Apr 2019, 23:12 
Offline
Super User

Joined: 26 Jun 2018, 14:51
Posts: 529
Has thanked: 36 times
Been thanked: 89 times
Japsican wrote:
If it's a gas bubble (air or voc fumes) then you can deflate it with a very small syringe needle with no deformity to the top sheet. I work in a hospital so I have many needles and syringes available, and using an insulin syringe is the best because the needle is very small. Likely you know a diabetic and might be able to score one from them (an unused one please).

It's better than a plain needle because you can draw back the plunger on the syringe and it creates a vacuum where the bubble was. The negative pressure often "repairs" any stretching that may have occurred from the bubbling. It's really pretty cool to see... try it. I got the idea during a wound debridement procedure, we sometimes use a needle on blisters for wound culturing...goes perfectly flat.

(Side note: never attempt to drain a blister yourself, always let your body take care of it or go to a professional if you must)


Why didn't you say earlier?! I've been razor blading blisters for years lol.


Top
 Profile  
 


PostPosted: 03 Apr 2019, 00:15 
Offline
Ninja of the Holy Chtchet
Ninja of the Holy Chtchet
User avatar

Joined: 28 Feb 2014, 13:38
Posts: 2499
Location: Washington DC
Has thanked: 558 times
Been thanked: 503 times
Blade: TSP Balsa 3.5 DEF+
FH: Xiom Omega IV Asia 2.0
BH: Xiom Vega Europe 2.0/Max
Haha... never came up here... but that PSA has been out there for years.

--- unless you're talking about the rubber blister air bubble issue --
I did mention that in a few other places.

_________________
Blog: "Holy Chtchet!"

Projects: Player Equipment Grid
Comprehensive Thin Inverted Chopping Rubbers Grid ⇝ Please send me corrections or new submissions


Top
 Profile  
 
PostPosted: 03 Apr 2019, 02:34 
Offline
Goes to 11
Goes to 11
User avatar

Joined: 13 Jan 2014, 20:27
Posts: 9699
Has thanked: 2 times
Been thanked: 1196 times
lasta wrote:
I find it easier to iron with the topsheet up. But it really depends on which side you intend to keep. Takes longer to iron through the sponge. I haven't had any damages either way, but make sure the bond is softened enough before peeling or you will get the stretching or even ripping problem. Warning, some rubbers (ESP ESN inverted) are VERY hard to separate.


These are pips out, don't know if ironing would work. Hot/boiling water's been suggested by an earlier poster.

Iskandar


Top
 Profile  
 
PostPosted: 03 Apr 2019, 03:14 
Offline
Super User

Joined: 25 Jan 2012, 01:53
Posts: 407
Location: canada
Has thanked: 1 time
Been thanked: 50 times
Blade: dr neubauer firewall +
FH: DHS skyline 3 neo 2.15 mm
BH: Dr. Neubauer Agressor 1.5
I tried in boiling water. No success, No even a small centimeter :envy:


Top
 Profile  
 
PostPosted: 03 Apr 2019, 04:35 
Offline
OOAK Super User
OOAK Super User
User avatar

Joined: 09 Oct 2008, 00:48
Posts: 2296
Location: Redwood City, California
Has thanked: 25 times
Been thanked: 158 times
Blade: BBC
FH: SP
BH: LP
Rubber sheet on your ironing board, pips side down. Old towel on top of sponge. Clothes iron set on low-med, no steam. Press firmly onto towel, focusing on one corner of the rubber sheet at first. Occasionally check temperature of foam and whether you can start to separate the top sheet from said foam. Getting the first corner started can be difficult. Once you get it, pull the warmed sponge away from the top sheet being careful not to tear the sponge. You'll only be able to separate about an inch at a time. Repeat the warming process and separate more of the sponge until you've got the entire sheet separated. Using too little heat will leave globs of adhesive on the top sheet that will then be impossible to remove. Using too much heat will melt something! So experiment with what works best with your particular set up. It's not as hard as it sounds!


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 20 posts ]  Go to page Previous  1, 2



All times are UTC + 9:30 hours


Who is online

Users browsing this forum: No registered users and 17 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Copyright 2018 OOAK Table Tennis Forum. The information on this site cannot be reused without written permission.

Powered by phpBB® Forum Software © phpBB Group