OOAK Table Tennis Forum

I'm a newcomer to this forum - in fact, this is only my second post. I won't rehash my "Introduce yourself" post, but given the topic of this post, I thought a little background would help provide some context.

I'm just getting back into the sport after playing recreationally in high school (many years ago). I don't own a table, I don't belong to a club, and I don't have a rating. (yet) But, I've been enjoying playing again over the past few months on the table at work, and I've been getting some intro coaching from a friend who competes, so it's a start. I got re-interested in the sport after I offered to try my hand at building a custom blade for that same friend. Yeah, I know - I've got no understanding of the engineering aspects of paddle design and material selection, but I'm no stranger to woodworking, and I thought it would be a fun project. Many google searches on "paddle building" later, I had uncovered a number of postings (here and elsewhere) by people who were curious about building their own blade, but I didn't run across very much in the way of instructions on how to do it. So, I started playing around with some ideas and making some paddles in my basement workshop. After a number of iterations and combination of materials, I arrived at a recipe for a decent paddle. I thought I'd share a mostly pictorial how-to for those who are interested in making a blade of their own. And, of course, this is just one way to go about it. I used the tools that I had available.

Tonight's menu:

A 5-ply blade, consisting of
a delicate 3/16" balsa core sandwiched between 2 layers of mahogany veneer on either face
surrounded with a 1/16" ash edge veneer
served with a conic lacewood handle
finished off with a hand-rubbed poly anglaise

Start off with a 6.25" x 11.5" sheet of balsa (http://www.nationalbalsa.com) and cut the mahogany veneers for each side. The interior veneer grain is oriented transversely.




I used Titebond veneer glue, which dries noticeably harder than regular carpenter's glue.


Apply the glue to the balsa substrate, then apply the veneer. I immediately coated the interior veneer with more glue and applied the outer veneer. I used a rubber roller to help set the veneers into the glue.



I glued one side at a time, but if you work fast, you can get veneers glued on both sides before clamping. I have a vacuum press, which makes clamping a bit easier. Here, I wrapped the glue-up in poly sheeting to keep the glue off of the granite platens that are used to keep everything perfectly flat.



These are just some partial granite tiles that I had leftover from another project.



A vacuum press requires a breather layer so that the air can easily be evacuated from the bag. This is poly batting from the fabric store.



The vacuum press generates about 12-13 psi clamping pressure. Over the face of the platens, that works out to be about 1200 lbs.



After gluing both sides, here's the finished blade blank.



Next installment: the blade template.

_________________
Ross
Handcrafted Table Tennis Blades

Pretty amazing photos. Thanks for posting.

_________________



The MNNB Blog has had some pretty amazing stuff lately. Just click this text to check it out. | My OOAK Interview
Table Tennis Video Links: itTV | laola1.tv | ttbl | fftt | Challenger Series | mnnb-tv

My whole set-up costs less than a sheet of Butterfly Dignics

I started of drawing a pattern that will be used to make a template. To get a symmetric pattern, I traced a half blade shape on paper, folded down the centerline, and cut out the double layer of paper. The handle section I extend about 1/2" past where I expect to cut it off ultimately.







Now, you could take this pattern and trace it directly on to the blade blank. But, I've been making blades of the same shape so that cut rubbers can be moved from one to another easily. A paper pattern is flimsy (and it won't work as a router template), so I transfer the outline of the pattern to some 3/4" mdf to use as a template.





Template rough-cut with a jigsaw and then smoothed on a sanding table.





Now that the template's complete, it's ready to be used to cutout the blade. I'll be doing that on a router table with a flush trim bit. I use foam double-stick tape to temporarily attach the template to the blade blank. This usually leaves a little goo on the blade, but it's easily sanded off.





Here's the blade trimmed on the router. The bearing on the flush trim bit rides along the template and cuts the blade to the exact same shape. I do this outside because of the noise and the flying sawdust.



It takes about 1 minute (I'm guessing) to cut out the blade on the router this way.



And the blade steps on the scale for the first time.



Next installment: ash edge trim

_________________
Ross
Handcrafted Table Tennis Blades

That's really cool,
thanks for sharing with us.

_________________
Chasse Patate

The balsa is nice and light, but it's very fragile and the exposed edges can be damaged easily. Ash veneer is a perfect way to protect the balsa. It's a tough wood, and it's very flexible. On the tablesaw, I cut a slightly oversized strip of 1/16" ash veneer. It takes a length of about 28"-30" to go around the blade allowing for some excess.



I wet down the strip and then started bending it around the perimeter of the blade. I clamped it in place and let the damp wood dry.



After the ash veneer dried, I applied a bead of glue to the edge of the blade, and then used a load of rubber bands to hold the ash veneer in place. Without the vacuum press, I would have added more rubber bands to ensure good contact all along the perimeter of the blade.



The vacuum press provides uniform pressure all along the edge.



After the glue set for a couple hours, I trimmed the end of the blade to final length and glued-on an end strip of veneer.




Next installment: making the handle

_________________
Ross
Handcrafted Table Tennis Blades

I used some lacewood for the handle. I cut 2 pieces around 3/8" thick and 4" long. I marked the handle outline and rough cut off the excess.





Again, I used the foam double-stick tape to temporarily hold the two handle halves together.



Using the bench sander, I sanded down the edges until they were just fractionally smaller than the blade tang.



With the handle pieces shaped to the correct width, I marked some bevel lines and headed back to the sander. Rounding over the handle pieces could also be done on the router, but I was too lazy to swap out the trim bit for a roundover bit (which wouldn't quite give me the shape I wanted anyway).



After beveling down to the reference lines on the bench sander.





After sanding down to a rough shape, I continued to smooth down the handles until they each had the same rounded contour. At that point, I separated the two halves and used the sanding spindle to create cove at the narrow end of the handle. Manufactured blades seem to consistently use a flat cut edge at the top of the handle, but I like the extra grip provided by a coved edge.



Next installment: putting it all together.

_________________
Ross
Handcrafted Table Tennis Blades

The final blade-sans-handle hits the scale for a weigh-in. This is after the edge veneer has been sanded down to final thickness.



I applied glue to the handle halves, applied them to the blade and held it in the proper position with some rubber bands. I also popped the whole thing into the vacuum press to clamp the handle while the glue dried (not shown).



Another hop on to the scale after a final sanding of the handle.



And finally, a finished blade with 2 coats of hand-rubbed poly to seal it (which is a good idea with mahogany).







There you have it. Raw materials to finished blade in a weekend. I hope that this helps someone out there who has been thinking about building one for themselves. Here's a stack of paddles that I've built using this process (the two in the foreground using the ash veneer edge).



Best of luck,
Ross

_________________
Ross
Handcrafted Table Tennis Blades

Very nice. But is the edge veneer legal? In an official tournament, might a referee not want to inspect what the blade is made off? With such an edge trim it is impossible to see whether, for instance, the blade is more than 85% wood. I think there is also something in the ruling about the plies of the blade needing to be continuous.

Simply beautiful.
How long does it take you to make one?
I have made a 1-ply blade, but nothing this great.

Would you consider making them for other people?

Very nice worksmanship! If only I'm not living so far away, I would love to use your blade and give them a try!

Why am I living across the ocean!

_________________
Yasaka Musashi JPen, Palio Macro Era 42.5 2.0mm, 122g
Butterfly Korbel FL, FH: Mark V XS 2.0 Red, BH Mark V M2 Max Black. 196g
Nittaku ??? SH Blade with 729 FX 2.2 on both sides, its only 30g without rubber [Retired]
Butterfly ??? PH Blade with 729 Hero 2.0 Black on FH, 755 OX Red on RPB. [Broken]

Wow fantastic thread and great pictures Ross Leidy!

_________________
OOAK Table Tennis Shop | Re-Impact Blades | Butterfly Table Tennis bats
Setup1: Re-Impact Smart, Viper OX, Victas VS 401 Setup2: Re-Impact Barath, Dtecs OX, TSP Triple Spin Chop 1.0mm Setup3: Re-Impact Dark Knight, Hellfire OX, 999 Turbo
Recent Articles: Butterfly Tenergy Alternatives | Tenergy Rubbers Compared | Re-Impact User Guide

Wow, those look very nice. Great woodworking skills.

I ran the edge strips just around the head so you can still see the layers.
You are the first person I know that uses a vacuum press. I do also. Very controllable pressure. Depending on the glue, less pressure can make a faster blade, thicker, hard glue layer.

Thanks for all the kind words. Let me answer some of the questions that were asked.


That was a concern of mine as well. My friend contacted someone who has umpired in European and world championships, and he said that he'd never seen a challenge to validate the 85% rule. Also, here haggisv references a blade manufacturer that uses a similar edge banding.


Thanks. Much of the time is spent waiting for glue to dry. The one shown above I made over last weekend, including making the template. I'd consider making some for other people, however, given my lack of experience in TT, I don't fully understand the consequences of my material selection. caveat emptor.


Thanks. Regarding how the blade plays, I'm woefully inadequate to describe. For my friend, he found the the (2)mahogany-1/4" balsa-(2) mahogany was too fast for the rubber he settled on. The same paddle built with 3/16" had a little more flexibility and he found that it provided the control he wanted. I'm playing a similar blade with (2)walnut-3/16" balsa-(2)walnut, with a purpleheart handle. (It's in the picture above. The purpleheart was 1/3 of the weight of the paddle! ) I'm using 729-8 on it. I'm happy with it for now - until I gain the skills to evaluate one blade against another.

Ross

_________________
Ross
Handcrafted Table Tennis Blades

If you play at a club, maybe you could put some rubbers on it and ask experiences players to have a hit with it and see how they describe it? I certainly hope they play well, because if so, that is basically a flawless blade.