OOAK Table Tennis Forum

After some testing I found that Yinhe/Galaxy Jupiter II worked very good for me. It is rather soft both sponge and top sheet so no need for boosting more than it comes from the factory. It may not be just as tacky as H3 but it can generate lots of spin since it is softer. And it has good speed on high impact, but is also controlled in blocking and short game. Blocking is perhaps bot has good as H3 but good enough for me (may be blade dependent). Serving is very good as well as looping against back spin.

Only weak part would perhaps be smashing, but I am not a smasher so someone else has to fill in here.

Anyway - this rubber is well worth a try and it has tremensous value per invested dollar since it is rather cheap.

I will have to report back on durability but so far, 3 months, has not caused any major differences in behavoiur of this rubber. So I am very happy .

_________________
My blog: Def-attack's attempts to find balance between defence/attack | Serving techniques and strategy section

T4 Racket Coverings wrote:

6. Gloss (shininess)
An acceptable surface is one whose measurement of 60 degree specular gloss using ASTM procedure D523 does not exceed 24* gloss units.

M-ATTACK Yinhe. The real "matt" topshit. Luminosity reduced down to 14 Gloss Units.
DHS Hurricane3 insane glisten of 22 Units to hurt your eyes.

Not sure what your point is, on several levels:

1) How is this related to the topic?
2) Other than rubber whose photograph you provided being from the same manufacturer as the rubber mention in the previous comment, how does it relate to the most recent discussions on this thread?
3) Both numbers you cite (14 and 22) are *lower* than the number you cite from the racket coverings spec, so again, what's your point? That they're within acceptable parameters?
4) And most importantly, the spec actually cites a *percentage* - which is complete nonsense. Percentages are used as a measure of reflection of incident light, as an *alternative* to gloss units, for exceptionally lustrous surfaces.

So... other than being off topic, irrelevant, and fundamentally confused with respect to using the units for specular reflection (although I grant you didn't write them), what exactly was your point?

_________________
"When one eye is fixed upon your destination, there is only one eye left with which to find the Way."

Read my blog: "LordCope's Latest Learnings Log": http://ooakforum.com/viewtopic.php?f=58&t=24452

Tacky chinese. Specifically the mega boosted ones from the factory. eg: Big Dipper. Lasts for ages and plays well even when the booster is gone. In fact I've got a multi year old sheet on my blade right now and it's much spinnier than Mantra or Mx-p, even though those are only a few months old. Although this big dipper is so old it no longer has any tack, it wasn't stored in my closet with a protector sheet. Yet it's still mega spinny.

H8 is also spinnier than the euro rubbers, but harder and not as nice to play with as the boosted rubbers. I think the heavily factory boosted rubbers are the way to go.

This H3 topshit - it's too bright my precious.. take it away!!! It burnses our eyeses!! It burnses! It burnses!! Gollum gollum.

Iskandar

A semi-tacky Joola Golden Tango PS that I've tried is the spinniest rubber with ABS ball I've seen so far. Especially on serves, I think

I have a two month old skyline TG2 Neo sheet that held a ball over night (7-8 hours) before I had to actually leave and take my equipment with me. I’m sure that thing would still be holding now if I didn’t have to go...

I use Nittaku sheet protectors and only use my breath for cleaning after play. The rubber sees ~6 hours of play a week.


Sent from my iPhone using Tapatalk

As you describe your setup and style try Ynghe Big Dipper and you'll have a great surprise. I am using one of these rubbers with maximum sponge on FH and LP ox on BH. I have the same style def close to the table combined with soft loops. The feeling is great. Try this rubber and believe me it's not expensive and you'll be pleased. Good Luck !

If you look on Yinhe's website you'll see new versions of Big Dipper (probably different sponge). Problem is I can't find any of them on any of my regular sources.

I think it's time to check back with Gambler - I was wanting to get some sheets of their new Volt-M and Volt-T rubbers with the new Otoro sponge. Mek-tek 9 with the Otoro sponge is already available.

Iskandar