OOAK Table Tennis Forum
https://ooakforum.com/

Rokphish Ramblings
https://ooakforum.com/viewtopic.php?f=58&t=30275
Page 20 of 23

Author:  rokphish2 [ 12 Feb 2024, 13:20 ]
Post subject:  Re: Rokphish Ramblings

Image

Author:  rokphish2 [ 13 Feb 2024, 14:53 ]
Post subject:  Rokphish Ramblings

Image

Author:  rokphish2 [ 14 Feb 2024, 15:59 ]
Post subject:  Re: Rokphish Ramblings

Image

Author:  rokphish2 [ 15 Feb 2024, 21:18 ]
Post subject:  Re: Rokphish Ramblings

Image

Author:  Debater [ 17 Feb 2024, 09:19 ]
Post subject:  Re: Rokphish Ramblings

rokphish2 wrote:
Image

That's a striking colour! Very vivid too. Nice :up:

Author:  rokphish2 [ 17 Feb 2024, 11:35 ]
Post subject:  Re: Rokphish Ramblings

Debater wrote:
rokphish2 wrote:
Image

That's a striking colour! Very vivid too. Nice :up:
Thank you!

Author:  rokphish2 [ 17 Feb 2024, 11:39 ]
Post subject:  Re: Rokphish Ramblings

Image

Somewhere in China…

Author:  rokphish2 [ 22 Feb 2024, 11:54 ]
Post subject:  Re: Rokphish Ramblings

Image

Author:  rokphish2 [ 24 Feb 2024, 22:06 ]
Post subject:  Re: Rokphish Ramblings

Image

Author:  rokphish2 [ 26 Feb 2024, 13:09 ]
Post subject:  Re: Rokphish Ramblings

Image

Author:  haggisv [ 26 Feb 2024, 14:06 ]
Post subject:  Re: Rokphish Ramblings

A bit more of a pain the cut the rubbers to size, isn't it! Good job though! :up:

Author:  rokphish2 [ 26 Feb 2024, 15:07 ]
Post subject:  Re: Rokphish Ramblings

haggisv wrote:
A bit more of a pain the cut the rubbers to size, isn't it! Good job though! :up:
Yes it is. Good thing the pips I use is so cheap. I was initially going to put new Vega Korea for the FH. But chickened out at the last minute so I don’t have other (cheap/er) new uncut rubber. I took one from another over size blade and it looks horrible but did the job for testing the blade for now. Ha!

Image

Author:  rokphish2 [ 26 Feb 2024, 15:11 ]
Post subject:  Re: Rokphish Ramblings

I’m going to need smaller scissors. The first wing is hard to cut with the big one I have. I started the cut from the first side and cut the rest and went back to cut the first wing from another angle. What a pain. Don’t have problem with regular shape blades.

Image

Author:  rokphish2 [ 26 Feb 2024, 15:18 ]
Post subject:  Re: Rokphish Ramblings

I usually start with the green arrow and cut counter clockwise. But for this one is hard to do. So I start from the side with the red arrow and cut counter clockwise. And then go back and cut the first wing from another angle (blue arrow). Can’t get a flushed cut with this angle though. Sticking out a little on this part.

Image

Author:  haggisv [ 26 Feb 2024, 15:27 ]
Post subject:  Re: Rokphish Ramblings

I still use a box-cutter knife, but it's tricky to get through the corners, you have to make sure the knife is very sharp. A scalpel would make it easier but they're a lot more expensive if you want the good ones.

Page 20 of 23 All times are UTC + 9:30 hours
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/