| OOAK Table Tennis Forum https://ooakforum.com/ |
|
| Rokphish Ramblings https://ooakforum.com/viewtopic.php?f=58&t=30275 |
Page 20 of 22 |
| Author: | rokphish2 [ 12 Feb 2024, 13:20 ] |
| Post subject: | Re: Rokphish Ramblings |
|
|
|
| Author: | rokphish2 [ 13 Feb 2024, 14:53 ] |
| Post subject: | Rokphish Ramblings |
|
|
| Author: | rokphish2 [ 14 Feb 2024, 15:59 ] |
| Post subject: | Re: Rokphish Ramblings |
|
|
| Author: | rokphish2 [ 15 Feb 2024, 21:18 ] |
| Post subject: | Re: Rokphish Ramblings |
|
|
| Author: | Debater [ 17 Feb 2024, 09:19 ] |
| Post subject: | Re: Rokphish Ramblings |
rokphish2 wrote: That's a striking colour! Very vivid too. Nice 
|
|
| Author: | rokphish2 [ 17 Feb 2024, 11:35 ] |
| Post subject: | Re: Rokphish Ramblings |
Debater wrote: rokphish2 wrote: That's a striking colour! Very vivid too. Nice |
|
| Author: | rokphish2 [ 17 Feb 2024, 11:39 ] |
| Post subject: | Re: Rokphish Ramblings |
 Somewhere in China… |
|
| Author: | rokphish2 [ 22 Feb 2024, 11:54 ] |
| Post subject: | Re: Rokphish Ramblings |
|
|
| Author: | rokphish2 [ 24 Feb 2024, 22:06 ] |
| Post subject: | Re: Rokphish Ramblings |
|
|
| Author: | rokphish2 [ 26 Feb 2024, 13:09 ] |
| Post subject: | Re: Rokphish Ramblings |
|
|
| Author: | haggisv [ 26 Feb 2024, 14:06 ] |
| Post subject: | Re: Rokphish Ramblings |
A bit more of a pain the cut the rubbers to size, isn't it! Good job though!
|
|
| Author: | rokphish2 [ 26 Feb 2024, 15:07 ] |
| Post subject: | Re: Rokphish Ramblings |
haggisv wrote: A bit more of a pain the cut the rubbers to size, isn't it! Good job though! Yes it is. Good thing the pips I use is so cheap. I was initially going to put new Vega Korea for the FH. But chickened out at the last minute so I don’t have other (cheap/er) new uncut rubber. I took one from another over size blade and it looks horrible but did the job for testing the blade for now. Ha! 
|
|
| Author: | rokphish2 [ 26 Feb 2024, 15:11 ] |
| Post subject: | Re: Rokphish Ramblings |
I’m going to need smaller scissors. The first wing is hard to cut with the big one I have. I started the cut from the first side and cut the rest and went back to cut the first wing from another angle. What a pain. Don’t have problem with regular shape blades. 
|
|
| Author: | rokphish2 [ 26 Feb 2024, 15:18 ] |
| Post subject: | Re: Rokphish Ramblings |
I usually start with the green arrow and cut counter clockwise. But for this one is hard to do. So I start from the side with the red arrow and cut counter clockwise. And then go back and cut the first wing from another angle (blue arrow). Can’t get a flushed cut with this angle though. Sticking out a little on this part. 
|
|
| Author: | haggisv [ 26 Feb 2024, 15:27 ] |
| Post subject: | Re: Rokphish Ramblings |
I still use a box-cutter knife, but it's tricky to get through the corners, you have to make sure the knife is very sharp. A scalpel would make it easier but they're a lot more expensive if you want the good ones. |
|
| Page 20 of 22 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|